HJOJOA's profile - activity

Measure Addchiller Could you share the measure addchiller? Do you know if there is a chiller database for energy simulat

DESIGN BUILDER CFD BOUNDARY For a CFD simulation in designbuilder, a simple office box with one four ways supply and one

DESIGN BUILDER CFD BOUNDARY For a CFD simulation in designbuilder, a simple office box with one four ways supply and one

DESIGN BUILDER CFD BOUNDARY For a CFD simulation in designbuilder, a simple office box with one four ways supply and one

High equipment density loads Hi, Running a simulation in OPEN STUDIO with a small building with a high density load (91

High equipment density loads Hi, Running a simulation in OPEN STUDIO with a small building with a high density load (91

High equipment density loads Hi, Running a simulation with a small building with a high density load (91M2 and 300 Kw e

Thank you, It was very helpful for my works good.

Thank you for your answer, very helpfully.

Plant loop turn on/off chiller in same plant loop In a chiller water plant using a combination of absorption chillers/el

Plant loop turn on/off chiller in same plant loop In a chiller water plant using a combination of absorption chillers/el

Plant loop turn on/off chiller in same plant loop In a chiller water plant using a combination of absorption chillers/el

Air cooled chilled water plant with freecooling in openstudio Dear, In a simulation of chilled water plant, one chiller

HI, I have found my mistake, the mistake is in the way i'm calculating the EIRFPL coefficient, thanks for your help. Now

In this link you will find the excel file, openstudio file and epw file (https://we.tl/t-nZJX9eqtFK), if you have any d

In this link you will find the excel file, openstudio file and epw file (https://we.tl/t-nZJX9eqtFK), if you have any d

In this link you will find the excel file, openstudio file and epw file (https://we.tl/t-nZJX9eqtFK), if you have any d

I have checked the COP hourly, is easy to see in results because COP never rise above 6 and according manufacturer when

I have checked the COP hourly, is easy to see in results because COP never rise above 6 and according manufacturer when

Can i share to you the files and check?

Also i have made a new simulation with HAP and the hourly simulation result is similar to manual calculation

And when you multiply the electric power calculated in EP by partial load, the result is very similar to manufacturer da

Hi, thanks to take time to review and help me, yes the chiller is ELECTRIC EIR, but i have tried different options, Cond

Chiller EIR higher than expected Hi, In a single air cooled chiller project, REF capacity is 320.7 KW at 35 C outdoor t

Chiller EIR higher than expected Hi, In a single air cooled chiller project, REF capacity is 320.7 KW at 35 C outdoor t

Chiller EIR higher than expected Hi, In a single air cooled chiller project, REF capacity is 320.7 KW at 35 C outdoor t

Hi, i have suffered the same issue with complex drawing and the problem still continue, but i can move forward using the

Hi, i have suffered the same issue with complex drawing and the problem still continue, but i can move forward using the

Chiller water plant with absorption chiller with recovered heat source Hi, I'm trying to model a chiller water plant us

Chiller water plant with absorption chiller with recovered heat source Hi, I'm trying to model a chiller water plant us

Thankyou, your advice's was very helpful, i tried in excel and coefficients in regression works good.

I dont know why but the coefficients i have are the result of the curvefittool

Can you share to me the parameter list you fed to the curvefittool? maybe i'm choosing the wrong dataset.

Than you, your coefficients are ok, i have tested, i will check the way i'm calculating this coefficients, thanks a lot.

First, thank you to take the time to answer, the chiller is Electric EIR, but i have tried with other EP chiller and the

First than you to take the time to answer, the chiller is Electric EIR, but i have tried with other EP chiller and the r

Ok, thank you for your help, for clarification, can you check if it is the right way to writhe in the curvefittool: Fo

That mean i'm entering in wrong way the data in the curvfittool to generate the "Electric Input to Cooling Output Ratio

Chiller COP calculation wrong Hi, I have created vfd compressor Electric chiller using manufacturer data for typical of

Chiller COP calculation wrong Hi, I have created vfd compressor Electric chiller using manufacturer data, but when runn

https://wetransfer.com/downloads/090b9c5524193c2520fc7e4c7437851d20180511203507/9e696a35f5026c20244d1901f2ca8ac620180511

Hi, I tried again, create new file, run first ideal loads with 160 Kw and works good, but then i added a new air loop an

High density load in datacenter Dear Unmet team, Running a simulation for a datacenter project, in a 200 M2 IT room wit

High density load in datacenter Dear Unmet team, Running a simulation for a datacenter project, in a 200 M2 IT room wit

Hi,

I´m trying to simulate a one thermal zone datacenter with a precision cooling air conditioning system, formed by a water condenser dx coil (water to air heat pump zone equipment) and a water coil, located in Bogota Colombia. Some hours at the day, its very common to use dry coolers fore full dx operation, several hours at the day we can use the dry cooler with water-cooled dx system and water coil at the same time (partial indirect free cooling), ant other hours total indirect freecooling to cool the datacenter.

The thing is the coil an the zone equipment are in the same water loop, the question is. How can i set the coil operation to be available only when the water loop temperature leaving the dry cooler is below the air supply temperature, and turn off the dx coil when the water loop leaving the dry cooler is below 60°F.

In the water loop, which set point manager is better for dry coolers? If there are two different system in the water loop (cooling water coil and water to air heat pump) which loop type do i need to set? cooling, condenser ? C:\fakepath\DATACENTER.jpg

Hi,

Modeling a building with OPS interface, i found problems when intersect faces between zones (one above other), small surfaces created cause matching problems, this small surfaces are created when intersecting faces, how can i avoid this situation? or let the program work with these small surfaces? how can fix it when match in the drawing?

Is there a way to change the software tolerance to to allow the software to ignore these small areas?

Hi,

Can someone tell me, which version of OS has the space load tab in the open studio sketchup toolbar ? Is there a a way to load this tab?

Hello, can someone explain, how to control humidity with a single speed cooling coil DX? step by step