Rwadhwa910's profile - activity

ok thanks, i used the one with Zone HVAC Baseboard Conv Water and it worked. Thanks!

So I am looking to model residential radiators units which one would be the correct one , I am using Zone HVAC Baseboard

You can also see on this link https://drive.google.com/file/d/1Tl6gbLa_0nP84lfkCSXUBI-MRnU2WpGT/view?usp=sharing

You can also see on this link

Just uploaded again

Does anyone have any information if any DOE Prototype building uses Radiator for heating purpose? Does anyone have any i

Hi Denis, thanks for the reply, I attached a picture above in the question and it is a Baseboard Conv water instead of b

If you look above I have attached all the output variables that you asked for, they are quite high.

Simulation taking way too long Hi , I am working on a 23 story 600,000 sqft building, I am using multipliers, so I only

Hi, I cant reduce the zones and surfaces,I am already creating only 3 stories i a 23 story building.

No, I did not I am getting convergence error that is another question that I have asked, but based on this for 1/3rd of

Hi, I have done all these options, still it is taking a lot of time to run.

Simulation taking way too long Hi , I am working on a 23 story 600,000 sqft building, I am using multipliers, so I only

Simulation taking way too long Hi , I am working on a 23 story 600,000 sqft building, I am using multipliers, so I only

Severe ** CheckWarmupConvergence: Loads Initialization, Zone="L01-1 BR 10" did not converge after 25 warmup days. How s

Assigning Delta T for Boilers Hi I am working on a hot water loop and while selecting the Boiler, it does not show any D

Does anyone have any information if any DOE Prototype building uses Radiator for heating purpose? Does anyone have any i

Thanks for the reply, the issues it is a 70 story building with more than 200 zones.

Creating multiple zones when importing gbxml file in openstudio Hi I am importing gbxml file for geometry in openstudio,

In open studio or energy plus, I can find out in energyplus but not in OS.

Multi speed heat pump I am modeling an air source heat pump in Openstudio, I cannot find out multi speed heat pump which

I am trying to model PCMs but I am not able to find any guide to find out how to model PCMs in OS /EP. Can somebody tell me where can I find material on how to simulate PCMs?

@aaronboranian Thanks for sharing, I was able to look into the energy plus example idf file for PCM Materials , The scri

How to simulate PCM materials in Openstudio / Energyplus? I am trying to model PCMs but I am not able to find any guide

@petros dalavouras that was helpful, I followed your approach. Thanks!

How can I set a hardsized Outdoor air no for each zone in a HVAC system ? I have 5 zones assigned to a system and I want

Tool to analyze the Sql from energyplus? What is the best software to analyze the eplusout.sql file ? Currently I am usi

You can use the inbuilt tool in open studio for drawing a building. Click new and it will create a floorplan.json file f

Thanks I found it.

How can I change the air distribution effectiveness number in openstudio? Where can I change the air distribution effec

What setpoint manager to use to avoid reheat in Summer season? I am using Setpoint manager warmest with temp between 55

What setpoint manager to use to avoid reheat in Summer season? I am using Setpoint manager warmest with temp between 55

Thanks David Goldwasser

thanks @Davidgoldwasser

Where to find the measures? I see the bcl.nrel.gov site has been modified, but it does not show anything about where to

No heat rejection while using DX cooling coil I am using DX cooling coil and there is no energy consumed for Heat rejec

How to model hydronic panel radiators in openstudio? How to model hydronic panel radiators in OS and also can we model b

Is it possible to model transpired solar collector in Openstudio? Is it possible to model transpired solar collector in

Getting Error Unknown Construction. While Running a simulation I am getting an error regrading Unknown construction miss

Getting Error Unknown Construction. While Running a simulation I am getting an error regrading Unknown construction miss

Thanks, @macumber, I can do it this way what if there are 100 thermal zones in the model. I think in that case it will t