Airloop doesn't work

asked 2018-01-04 06:08:12 -0600

Fernando
71 ●5

updated 2018-01-04 10:26:13 -0600

I have a datacenter that consumes 18 kw. For cooling I created a loop for water: image description Also I created a loop for air:

The simulation crash and gives me the following error:

 ** Severe  ** AirLoopHVAC VC_DATACENTER has no air flow
 **   ~~~   ** Check flow rate inputs for components in this air loop and,
 **   ~~~   ** if autosized, check Sizing:Zone and Sizing:System objects and related inputs.

edit retag flag offensive close merge delete

add a comment

1

answered 2018-01-04 07:46:26 -0600

Avi
4320 ●2 ●11

As it reads you don't have air inlet. You need to darg AirloopHVAC:OutdoorAirSystem from the library to the upper left part of the plant. Later I guess you can set outside air to zero if that is what you need.

edit flag offensive delete link

add a comment

1

answered 2018-01-04 08:19:49 -0600

Julien Marrec

29716 ●94 ●76 http://www.effibem.com/

You don't need an AirLoopHVAC:OutdoorAirSystem at all.

The problem is that your loop is probably autosized, and it's getting sized to a zero flow. That can happen for a variety of reasons.

Check that the zone you serve does have a high cooling load (check the equipment and the schedules attached to it). Check that the zone also has appropriate thermostat setpoint schedules (eg 40F heating / 80F cooling). Also double check the Airloop Sizing:System and the zone Sizing:Zone inputs. And check the SetpointManager you placed on your AirLoopHVAC.

Note that if the only thing you're trying to cool down is a single zone, I'd suggest not using an AirLoopHVAC at all, but one of the ZoneHVAC object that can use a Coil:Cooling:Water (PTAC for example, or 4 pipe FCU)

edit flag offensive delete link

Comments

I considered a load of 500w/m2 and cooling setpoint temperature of 25ºC.What is the most recommended setpoint manager?

Fernando ( 2018-01-04 08:38:43 -0600 )edit

Cooling down a space with 25°C is unusual to me, and if you didn't change the sizing:system and sizing:zone, it certainly doesn't match the default values. I'd say 55°F if you use a scheduled one. Otherwise, if you're trying to only cool down, you can use a SPM:SingleZone:Cooling.

Julien Marrec ( 2018-01-04 08:47:00 -0600 )edit

I assume you meant a zone temperature set point of 25C. For water coils (for example used in fan coil units), the SPM:SingleZone:Cooling will place the operating set point temperature at the outlet node of the coil (you need to specify this node name in the SPM object). If a draw through fan is used, specify the SPM control node as the fan outlet node and then used a mixed air SPM to place the fan heat adjusted set point at the outlet of the water coil. For other HVAC systems (e.g., ZoneHVAC:PackagedTerminalAirConditioner or AirloopHVAC:Unitary:Furnace:HeatCool) you wouldn't need the SPM.

rraustad ( 2018-01-04 08:58:47 -0600 )edit

I did what you said. I put FCU unit, Temperature setpoint 15ºC, heating batery always off, but I get air temperature very high, like 100ºC. I think the fancoil doesn´t work.

Fernando ( 2018-01-04 09:14:43 -0600 )edit

Is the FCU turning on?

rraustad ( 2018-01-04 10:27:28 -0600 )edit

see more comments

0

answered 2018-01-04 16:17:55 -0600

Fernando
71 ●5

updated 2018-01-05 05:50:14 -0600

rraustad,

The three images show the datacenter's cooling system (chiller, fan coil), where the consumption is 18 kW. The air temperature obtained of the simulation is greater than 100 ° C. What´s is Wrong?