 | 1 | initial version |
Hey everyone :)
When I run the simulation in OpenStudio i get this message:
Is it because I didn't fill the HVAC/Thermal zone Tab? Anyone who could help, please?
Ps: I am using OpenStudio 2.5
Thanks :)
Hey everyone :)
When I run the simulation in OpenStudio i get this message:
Is it because I didn't fill the HVAC/Thermal zone Tab? Anyone who could help, please?
Ps: I am using OpenStudio 2.5
Thanks :)
Hey everyone :)
When I run the simulation in OpenStudio i get this message:
I also exported an IDF file from OpenStudio and tried to run a simulation with EnergyPlus, but I also had this message:
Is it because I didn't fill the HVAC/Thermal zone Tab? Anyone who could help, please?
Ps: I am using OpenStudio 2.52.5 and EnergyPlus 2.13.
Thanks :) :)
| | 4 | retagged |
Hey everyone :)
When I run the simulation in OpenStudio i get this message:
I also exported an IDF file from OpenStudio and tried to run a simulation with EnergyPlus, but I also had this message:
Is it because I didn't fill the HVAC/Thermal zone Tab? Anyone who could help, please?
Ps: I am using OpenStudio 2.5 and EnergyPlus 2.13.
Thanks :)
| | 5 | retagged |
Hey everyone :)
When I run the simulation in OpenStudio i get this message:
I also exported an IDF file from OpenStudio and tried to run a simulation with EnergyPlus, but I also had this message:
Is it because I didn't fill the HVAC/Thermal zone Tab? Anyone who could help, please?
Ps: I am using OpenStudio 2.5 and EnergyPlus 2.13.
Thanks :)
| | 6 | retagged |
Hey everyone :)
When I run the simulation in OpenStudio i get this message:
I also exported an IDF file from OpenStudio and tried to run a simulation with EnergyPlus, but I also had this message:
Is it because I didn't fill the HVAC/Thermal zone Tab? Anyone who could help, please?
Ps: I am using OpenStudio 2.5 and EnergyPlus 2.13.
Thanks :)
| | 7 | retagged |
Hey everyone :)
When I run the simulation in OpenStudio i get this message:
I also exported an IDF file from OpenStudio and tried to run a simulation with EnergyPlus, but I also had this message:
Is it because I didn't fill the HVAC/Thermal zone Tab? Anyone who could help, please?
Ps: I am using OpenStudio 2.5 and EnergyPlus 2.13.
Thanks :)
Hey everyone :)
When I run the simulation in OpenStudio i get this message:
I also exported an IDF file from OpenStudio and tried to run a simulation with EnergyPlus, but I also had this message:
Is it because I didn't fill the HVAC/Thermal zone Tab? Anyone who could help, please?
Ps: I am using OpenStudio 2.5 and EnergyPlus 2.13.
Thanks :)
EDIT: So I opened the *.err file to have details about the error, as suggested, and I had this message:
Program Version,EnergyPlus, Version 8.9.0-eba93e8e1b, YMD=2018.07.20 12:31,
* Severe * <root>[Construction][ASHRAE 189.1-2009 ExtRoof IEAD ClimateZone 1] - Missing required property 'outside_layer'.
* Severe * <root>[Material][Exterior door][specific_heat] - "0.100000" - Expected number greater than or equal to 100.000000
* Fatal * Errors occurred on processing input file. Preceding condition(s) cause termination.
...Summary of Errors that led to program termination: ..... Reference severe error count=2 ..... Last severe error=<root>[Material][Exterior door][specific_heat] - "0.100000" - Expected number greater than or equal to 100.000000
*** Warning: Node connection errors not checked - most system input has not been read (see previous warning).
*** Fatal error -- final processing. Program exited before simulations began. See previous error messages. strong text *** EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors. *** EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors. *** EnergyPlus Terminated--Fatal Error Detected. 0 Warning; 2 Severe Errors; Elapsed Time=00hr 00min 0.63sec
But I did not understand the third one (the Fatal one), So if anyone could help ?
Thanks again :)
