Question-and-Answer Resource for the Building Energy Modeling Community
Get s tarted with the Help page
Ask Your Question
1

Hi! Does anyone know how can I model a technical floor in designbuilder and how can I add a LECU?

asked 2018-05-02 07:27:20 -0600

andreea gravatar image

updated 2018-05-02 11:17:32 -0600

I need to add a LECU( Local Environmental Control Unit) in my model.

edit retag flag offensive close merge delete

Comments

If in understand correctly what you want to model is more often called a "Raised Floor", with "Underfloor Air Distribution" (UFAD). There are examples of such systems in EnergyPlus Examples/ directory, and other questions on this site may help too: https://unmethours.com/questions/quer...

Julien Marrec gravatar image Julien Marrec  ( 2018-05-02 07:45:58 -0600 )edit

2 Answers

Sort by ยป oldest newest most voted
1

answered 2018-05-04 04:50:12 -0600

kksharma3951 gravatar image

to add technical floor or false ceiling, they best way to do is by making a new zone and selecing it as an plenum or you can also model it by using floor void in construction tab.

edit flag offensive delete link more

Comments

1

I designed the plenum part and after that i took the picture above and the errors.

andreea gravatar image andreea  ( 2018-05-07 09:17:28 -0600 )edit

Can you share the screenshot of the error? i am guessing you need to activate internal source from construction tab. Generally when you have any radiant source for heating/cooling the internal source needs to be activated. Refer to slide number 40-46 from the link below: http://www.beepindia.org/sites/defaul...

kksharma3951 gravatar image kksharma3951  ( 2018-05-09 01:19:21 -0600 )edit

I could just add the photo above, I hope you understand. So what the project ask me to do is the following: I have the concrete slab inside which I have the heat and cooling source, then I have an air gap for the recirculated air coils heated and cooled by the preference through convective systems by and through floor(thats why i think the firs section is the correct one). This system also incorporates the fresh air supply system through the floor. The fresh air that is distributed inside the building is produced in recovery CTAs temperature and humidity.

andreea gravatar image andreea  ( 2018-05-09 02:46:27 -0600 )edit
1

answered 2018-05-07 08:50:23 -0600

andreea gravatar image

updated 2018-05-09 02:39:13 -0600

thank you for your answers! the idea is that I have both technical floor space and heating and cooling in the concrete slab. so I designed a system in builder design, but I do not think it's correct because it gives me error when simulating: zone is specified as having a radiant surface but no radiant surface in the zone have an internal source set in their constructionimage descriptionimage description

edit flag offensive delete link more

Comments

I left the same hvac system but I put the internal source in two different places and these are the errors. The first section is right for my model but I have those errors.I read in the manual that to make a plenum I have to replace the splitter/mixer with the supply plenum/return plenum ,which I have done. On the floor void writes that: if the floor construction already has an air gap for the floor void and its thickness is used to define the inner volume then you should enter 0 here. (I do not know if it considered floor void the air gap that i left in construction)

andreea gravatar image andreea  ( 2018-05-09 02:37:37 -0600 )edit

Your Answer

Please start posting anonymously - your entry will be published after you log in or create a new account.

Add Answer

 

Question Tools

1 follower

Stats

Asked: 2018-05-02 07:27:20 -0600

Seen: 436 times

Last updated: May 09 '18