First time here? Check out the Help page!
2023-09-25 11:45:11 -0500 | answered a question | Chiller not meeting set point with waterside economiser I've had trouble with HeatExchanger:FluidToFluid control is DesignBuilder as well. A few things I'd suggest, some of whi |
2022-05-27 06:21:02 -0500 | received badge | ● Rapid Responder (source) |
2022-05-27 06:21:02 -0500 | answered a question | energy consumption increase with ERV? I've seen increases in energy use with ER in AHUs in models before. Usually, switching the "Supply Air Temperature Contr |
2022-01-07 06:09:17 -0500 | answered a question | How to model VFR ODU with AHU in DesignBuilder Hey, fellow DesignBuilder user here. I actually sent a support ticket to DesignBuilder a few years ago regarding this, a |
2021-09-21 07:01:10 -0500 | edited answer | Seeking advice to reduce excessive interior lighting electricity use in baseline model using ASHRAE measure Probably not the answer you wanted to hear, but I've run into this on many models. A similar thing can happen with windo |
2021-09-21 07:00:31 -0500 | answered a question | Seeking advice to reduce excessive interior lighting electricity use in baseline model using ASHRAE measure Probably not the answer you wanted to hear, but I've run into this on many models. A similar thing can happen with windo |
2021-09-21 07:00:31 -0500 | received badge | ● Rapid Responder (source) |
2021-07-22 05:46:15 -0500 | commented answer | Relative Humidity control in DesignBuilder This is where it always takes a little fussing for me to get the model to work. Check that you have one of the minimum h |
2021-07-21 10:07:33 -0500 | commented answer | Relative Humidity control in DesignBuilder You'd need an air system to go along with any radiant-type system (heated floor, chilled ceiling, etc.). Depending on yo |
2021-07-21 09:24:21 -0500 | commented answer | Relative Humidity control in DesignBuilder Any type of radiant system will only help meet sensible loads, so you'll still need another system for humidity control. |
2021-07-21 06:57:16 -0500 | answered a question | Relative Humidity control in DesignBuilder Debayan93, I don't believe DesignBuilder can do humidity control with only an FCU in the zone. Usually it requires an A |
2021-07-21 06:57:16 -0500 | received badge | ● Rapid Responder (source) |
2020-04-17 08:20:38 -0500 | received badge | ● Teacher (source) |
2020-04-16 14:43:43 -0500 | edited answer | EMS - load existing schedule value each timestep I was able to solve this. The key was using the <loopzoneattribute occupancyschedule=""> as the sensor Object IDF |
2020-04-16 14:43:43 -0500 | received badge | ● Editor (source) |
2020-04-16 14:43:30 -0500 | edited answer | EMS - load existing schedule value each timestep I was able to solve this. The key was using the <loopzoneattribute occupancyschedule=""> as the sensor Object IDF |
2020-04-16 14:40:38 -0500 | answered a question | EMS - load existing schedule value each timestep I was able to solve this. The key was using the <loopzoneattribute occupancyschedule=""> as the sensor Object IDF |
2020-03-03 12:06:42 -0500 | received badge | ● Student (source) |
2019-11-08 12:07:26 -0500 | asked a question | EMS - load existing schedule value each timestep EMS - load existing schedule value each timestep I'm trying to write an EMS program that will apply a Gaussian multiplie |