Nathalia's profile - activity

Four pipe fan coil with heating eletric in opensudio Hello, I'm running a simulation where certain zones have fan coils.

HVACTemplate:Zone:Fancoil I am simulating a building in EnergyPlus 9.1 with 428 conditioned zones. Out of these, 154 zon

Hi Keigo! Thanks for the answer. For me, reading item G3.1.2.3, it is not clear whether what is being required are the h

Unmet hours according Ashrae 90.1/2010 I have a question regarding the Unmet Hours required by ASHRAE 90.1/2010. I've al

Hello! I am using EnergyPlus 9.1 and I am using the AirFlow Network function. I need to generate the operating temperature results of 356 thermal zones. However, after finishing the simulation, when I open the .csv file, I don't have the result of all the thermal zones. This has happened twice with different files. I did a test running in OpenStudio and the result of the average temperature of all zones comes out there, but energy plus does not come out. I would like to know if there is a limit of thermal zones in the model, or what other error could be happening so that the temperature result in all thermal zones does not come out through Energyplus.

Thanks for the answer, it worked!

Output variable does not generate results for all thermal zones Hello! I am using EnergyPlus 9.1 and I am using the AirF

I can't install OpenStudio version 2.8 I'm trying to install OpenStudio version 2.8 on some newer notebooks. I can insta

How to create a Heat Recovery Ventilator (HRV) in openstudio? Hi, I am using openstudio version 2.8 and I need to model

I'm using version 2.8, does this measure only work in other versions?

How do I delete the measure from the directory?

Error using measure Air Wall Zone Mixing Hi, I am using OpenStudio 2.8 and when trying to use the measure "Air Wall Zon

How to represent fans for external air intake in openstudio? Hi, I'm simulating a 10-story office for LEED ID+C certifi

How to represent fans for external air intake in openstudio? Hi, I'm simulating a 10-story office for LEED ID+C certifi

How to represent fans for external air intake in openstudio? Hi, I'm simulating a 10-story office for LEED ID+C certifi

Thanks for the answer! I modeled it as you said, created the airloop with Outdoor Air Systems and left only the Ventilat

Thanks for the answer! I modeled it as you said, created the airloop with Outdoor Air Systems and left only the ventil

How to represent fans for external air intake in openstudio? Hi. I am doing the simulation for LEED ID + C v.4 certifica

Hi. I would like to know how I configure the plant loop in openstudio to have a primary and secondary pump if I am only

Model primary-secondary pump with only one baseline system Hi. I'm setting up the baseline following ASHRAE 90.1/2010 f

Thank you for your help. Using one of the options on page 137 of the ID+C guide I would need to have some information ab

Cooling tower in the simulation of the proposed model for LEED ID + C certification Hi! I am in doubt about the simulati

System 8 in OpenStudio has a CHW loop, but it doesn't have a CW loop, so my question is whether I should connect to the

It's not really an academic exercise, I'm doing LEED V4 certification for a restaurant inside the mall. LEED V4 uses ASH

Should the ASHRAE system 8 chiller be connected to the system 7 condenser in OpenStudio? Hi, I am modeling a baseline in

Reasons for Fans demand low in OpenStudio simulation I'm creating an Airloop in OpenStudio and the demand for fans is al

I don't know how to insert photos. I tried everything but it doesn't load

Reasons for Fans demand low in OpenStudio simulation I'm creating an Airloop in OpenStudio and the demand for fans is al

Reasons for Fans demand low in OpenStudio simulation I'm creating an Airloop in OpenStudio and the demand for fans is al

Reasons for Fans demand low in OpenStudio simulation I'm creating an Airloop in OpenStudio and the demand for fans is al

Thanks for the replies. I already watched these NREL videos and the current version of OpenStudio no longer has these op

OpenStudio measure AedgK12SlabAndBasement is not working I'm trying to insert the ground temperatures in my simulation m

Reasons for heating demand are higher than cooling demand, if cooling consumption is higher I'm creating an Airloop in O

Reasons for Fans demand low in OpenStudio simulation I'm creating an Airloop in OpenStudio and the demand for fans is al

Reasons for Fans demand low in OpenStudio simulation I'm creating an Airloop in OpenStudio and the demand for fans is al

Thanks for the replies. I already watched these NREL videos and the current version of OpenStudio no longer has these op

How can I view or generate Radiance Illuminance Map and Radiance scene rendering using Radiance Daylighting Measure in O

One more question, maybe you can help me. Do you know, if there is any report measure for open studio results, with meas

Yeah, very weird. But during the week I will do more testing in version 2.6.0, and when I go to version 2.7.0, I will re

On Friday I took the test and gave an error using the same models I sent you. This weekend I uninstalled and re-installe

sorry to say this but it did not work, it still gives the same error, to the windows facing north: "[effective-angle] -

follows the link with the files .osm: https://we.tl/t-rFWGvnPoLU Thanks.

I tried the two ways, inserting by the BLC and lowering the measure and putting in the "My measure", in both ways an err

I updated the measure in BLC, and it still gives the same error. This happens only with windows located in the north. I

The error that occurred was this: "* Severe * <root>[ZoneVentilation:WindandStackOpenArea][N-3-E-W-15-W-2_Windan