Siv's profile - activity

The total cooling load of the entire facility is only 2700 kW, however the autosized design coil load is 8600 kW, the nominal capacity of the chiller and tower are 8600 and 8100 kW respectively. There is no sharp changes in design day schedule. Yet, how does this oversizing occur ?

This particular CSV file (Please refer the image) was obtained from an EnergyPlus Simulation. The design day for this simulation is 05/21. The run period is also 05/21. Hence, both of them are same.

I take it that the variables in the upper half of the CSV file which is enclosed in a red box, corresponds to the design day values, and the rest belongs to run period.

So, I was wondering why they both are not the same ? eventhough my run period and design day are same!

Can someone please provide me the steps for openstudio installation in Ubuntu 16.04 ?

Someone please tell me what the Difference Between Peak and Estimated Sensible Load in the facilityloadcomponentsummary is ? what does the two terms mean ?

Difference Between Peak and Estimated Sensible Load Someone please tell me what the Difference Between Peak and Estimate

Difference Between Peak and Estimated Sensible Load Someone please tell me what the Difference Between Peak and Estimate

Redundant models types I was wondering why there many fan models eventhough they are the same ?

Redundant models types I was wondering why there many fan models eventhough they are the same ?

I have resolved the error by setting the Reference Temperature Type = OutdoorAirDryBulb in the Setpoint manager FollowOu

I reduced the supply air temperature and the issue was resolved. Looks like I was doing something which was not psychrom

Does anybody have an idea as to how this particular warning can be rectified or what causes this issue ?

SizeWaterCoil: Coil="CHW CLG COIL", Cooling Coil has leaving humidity ratio > entering humidity ratio.
   **   ~~~   **     Wair,in =  4.120009E-003
   **   ~~~   **     Wair,out = 8.912150E-003
   **   ~~~   ** ....coil leaving humidity ratio will be reset to:
   **   ~~~   **     Wair,out = 4.120009E-003

Energyplus : Calculation of cooling coil design UA failed for coil CHW CLG COIL Can anyone please tell me why this error

Cooling minimum air flow fraction ? Will the Sizing:Zone:Cooling Minimum Air Flow Fraction input still be used to set mi

My chiller is a water cooled chiller. I changed the Xmin, Xmax to 7, Ymin and Ymax values to 19 and 30 but still the er

Plant Loop:Demand Side is storing excess heat the majority of the time How to rectify the error "Plant Loop:Demand Side

Plant Loop:Demand Side is storing excess heat the majority of the time How to rectify the error "Plant Loop:Demand Side

I have posted the picture on top and yeah I have tried using intermittent pump setting also.

I am trying to add a water heater and I am trying to autosize the heater maximum capacity but it says

Warning ** Water heater named WATER HEATERhas heater capacity set to AUTOSIZE but it is missing associated WaterHeater:Sizing object
   **  Fatal  ** GetWaterThermalTankInput: Errors found in getting thermal storage input. Preceding condition(s) causes termination.

However, the fatal error disappears when I hardsize the heater maximum capacity. I believe this is a OpenStudio bug, can anyone clarify ?

My chiller is a water cooled chiller. I changed the Xmin, Xmax to 7 Ymin and Ymax values to 19 and 30 but still the err

Chiller curve and AHRI test condition. Hi It looks like the IPLV calculated for my chiller is not at AHRI test conditio

My chiller is a water cooled chiller. I changed the Xmin, Xmax to 7 Ymin and Ymax values to 19 and 30 but still the err

water heater sizing object missing in OpenStudio I am trying to add a water heater and I am trying to autosize the heate

I understand, however how does the warning not appear when I change the setpoint manager to "Setpoint Manager Single Zo

I understand, however how does it not appear when I change the setpoint manager to "Setpoint Manager Single Zone One St

Is the issue resolved ?

Yeah, is the issue resolved ?

My pump is continuous, I have included images of the pump settings and the loop settings

Plant Loop:Demand Side is storing excess heat the majority of the time How to rectify the error "Plant Loop:Demand Side

My pump is continous

It got resolved, I just had to wait for sometime.

SketchUp stuck after surface matching I tried to create three floors separately and I moved them on top of each other. W

Cooling Coil has leaving humidity ratio > entering humidity ratio Does anybody have an idea as to how this particular

Plant Loop:Demand Side is storing excess heat the majority of the time How to rectify the error "Plant Loop:Demand Side

I am sorry, this can be deleted. I was kinda making a presentation regarding how to sign up for Unmet hours.

done...………………….

I am trying to add frame and divider property to my sub surfaces, yet when i click on apply to selected, it vanishes off. Can some help ?

How do I sign up in Unmet Hours Hi, this is just a sample question. The context of your problem can be described here. P