Ali Raad's profile - activity

Electric equipment inputs Hello, I am working on a house model in EnergyPlus, and I need to add internal loads such as

IES-VE Energy Consumption on Zone level Hello, I am modeling a commercial building of 80 zones in IES-VE, I used the te

EnergyPlus heat recovery from a zone to heat another zone Hello everyone, I don't know if what I'm asking for is possib

EnergyPlus heat recovery from a zone to heat another zone Hello everyone, I don't know if what I'm asking for is possib

Hello,

I am working on a model in E+ and I would like to compare it to a model created on IESVE. In IESVE there is an output called Solar Gain.

It is defined by IESVE as "Solar gain: Solar radiation absorbed on the internal surfaces of the room, plus solar radiation absorbed in glazing and transferred to the room by conduction."

I have checked the output:variable in E+ and I have not found any output to match that. Could anybody help me with that? I would like to know what is the output:variable should I request for Solar Gain in a zone. Or if you have any other suggestion how can I compare the solar gain of the models please let me know.

Thank you very much, your help is highly appreciated.

Solar Gain in EnergyPlus Hello, I am working on a model in E+ and I would like to compare it to a model created on IESV

@rsunnam Thank you very much for your help, and have a great day.

Hello @rsunnam Thank you for your reply, I can not use auto-sizing in my model I need to use the exact manufacture spec

Hello @rsunnam Thank you for your reply, I can not use auto-sizing in my model I need to use the exact manufacture spec

ZoneHVAC:FourPipeFanCoil serving 2 different Zones!! Hello everyone, Is there anyway to model a ZoneHVAC:FourPipeFanCoi

ZoneHVAC:FourPipeFanCoil serving 2 different Zones!! Hello everyone, Is there anyway to model a ZoneHVAC:FourPipeFanCoi

Hello @rsunnam Thank you very much fro your answer, I really appreciate your help. Regarding the modeling 2 fan coil u

If the templates do autosize the capacity of the coil, then what I can do is to sum the Supply Air Maximum Flow Rate of

Hello @Raghu Sunnam Thank you very much fro your answer, I really appreciate your help. Regarding the modeling 2 fan c

If the templates do autosize the capacity of the coil, then what I can do is to sum the Supply Air Maximum Flow Rate of

Hello @Raghu Sunnam Thank you very much fro your answer, I really appreciate your help. Regarding the modeling 2 fan c

In that past I had many issues with surface matching and intersection. I was using OpenStudio 2.0.1 with Sketchup 2017.

Multiple HVAC templates in one zone issue!! Hello everyone, I am trying use HVAC templates in my model. Currently I am u

Multiple HVAC templates in one zone issue!! Hello everyone, I am trying use HVAC templates in my model. Currently I am u

Multiple HVAC templates in one zone issue!! Hello everyone, I am trying use HVAC templates in my model. Currently I am u

Multiple HVAC templates in one zone issue!! Hello everyone, I am trying use HVAC templates in my model. Currently I am u

Multiple HVAC templates in one zone issue!! Hello everyone, I am trying use HVAC templates in my model. Currently I am u

I had the same problem, after I saw your comment I did the same and it works very fine. Thank you.

Have you tried to increase the system capacity to more than 4000W, Have you tried to set higher water temperature at the

Thank you for your comment. actually I have autosized some component, I also thought that the autosized fields are tryin

Low Temperature Radiant tubing length Hello everyone, I am modeling a ZoneHVAC:LowTemperatureRadiant:VariableFlow, usin

Thank you, I really appreciate your help.

When I use Foundation boundary condition for the slab I can't get Surface Outside Face variables which is very understandable. However, is there anyway to be able to measure the temperature within the slab. Although I am using the CFD algorithm the nodes that is created inside the floor surface will not have any result I assume that is related to the fact that Foundation:Kiva does not use the same algorithm as the rest of the model.

Thank you very much. May I know what do think about running a simulation on E+ using Foundation as the outside boundary

Thank you very much. May I know what do think about running a simulation on E+ using Foundation as the outside boundary

Yeah, I'm really interested to know @Neal Kruis 's idea and recommendation regarding that issue.

Help: Foundation boundary condition (Foundation:Kiva)!! Hello everybody, When I use Foundation boundary condition for t

Thank you very much , I really appreciate your help. Regarding the ground that is exactly what I am planning to do. Than

Hello everyone,

I am planning to simulate a greenhouse using energyplus. May I know which algorithm is the best to use in E+ for solar radiation and heat transfer through transparent/semitransparent surfaces as well as heat transfer in soil? CFD or CTF?

Thank you

Help: which algorithm to use??? Hello everyone, I am planning to simulate a greenhouse using energyplus. May I know whi