First time here? Check out the Help page!
2019-05-04 00:37:14 -0500 | asked a question | how to sent the Water Plate Heat Exchanger in Design Builder how to sent the Water Plate Heat Exchanger in Design Builder I met a situation that the cooling system is the second pum |
2018-09-02 21:09:01 -0500 | asked a question | why the design builder export opaque surface conduction equal to inside faces total conduction heat but not attach to the outside face? why the design builder export opaque surface conduction equal to inside faces total conduction heat but not attach to t |
2018-08-30 21:51:33 -0500 | commented answer | what relationship among the Surface Outside Face,Surface Inside Face and Surface Average Face ? Do you have tried to export the report from the Design Builder,?I did a test and found that “Walls+Ground Floors+Roofs” |
2018-08-30 21:50:19 -0500 | marked best answer | what relationship among the Surface Outside Face,Surface Inside Face and Surface Average Face ? In the e+ help document ,I think that Surface Inside Face Conduction Heat Transfer Rate + Surface Outside Face Conduction Heat Transfer Rate = Surface Average Face Conduction Heat Transfer Rate,but it was not rihgt, so I want to konw their relationship. |
2018-08-30 21:50:12 -0500 | commented answer | what relationship among the Surface Outside Face,Surface Inside Face and Surface Average Face ? Do you have tried to export the report from the Design Builder,?I did a test and found that “Walls+Ground Floors+Roofs” |
2018-08-30 06:26:08 -0500 | asked a question | what relationship among the Surface Outside Face,Surface Inside Face and Surface Average Face ? what relationship among the Surface Outside Face,Surface Inside Face and Surface Average Face ? In the e+ help document |
2018-08-30 06:12:20 -0500 | commented answer | why cannot I export "Zone Opaque Surface Outside Face Conduction Gain" Can you explain ? I can't find my fault. I just export the IDF from DesignBulider to Energyplus. And I found that the “ |
2018-08-30 06:12:20 -0500 | received badge | ● Commentator |
2018-08-29 02:12:27 -0500 | commented question | why cannot I export "Zone Opaque Surface Outside Face Conduction Gain" my version is 8.1 |
2018-08-29 02:12:00 -0500 | asked a question | why cannot I export "Zone Opaque Surface Outside Face Conduction Gain" why cannot I export "Zone Opaque Surface Outside Face Conduction Gain" I can export "Zone Opaque Surface inside Face Co |
2018-08-27 05:03:22 -0500 | asked a question | It occur error when I put the IDF exported from Design Buider to Energyplus It occur error when I put the IDF exported from Design Buider to Energyplus It occur error that "Did not find "ProgramCo |
2018-08-27 05:03:20 -0500 | asked a question | It occur error when I put the IDF exported from Design Buider to Energyplus It occur error when I put the IDF exported from Design Buider to Energyplus It occur error that "Did not find "ProgramCo |
2018-08-15 17:23:09 -0500 | received badge | ● Popular Question (source) |
2017-05-24 22:53:39 -0500 | commented question | EMS to contorl idealloadairsystem on depond on the room temperture Yes,I want to control IdealLoadAirSystem operating schedule,can I ? |
2017-05-24 20:38:01 -0500 | asked a question | EMS to contorl idealloadairsystem on depond on the room temperture EMS to contorl idealloadairsystem on depond on the room temperture Now I want to set EMS contorl with IdealLoadAirSystem |
2017-05-24 19:45:40 -0500 | commented answer | temperature control;Tolerance temperature That is my falut and I start the new question. Thank you and I hope you can give me some advides. |
2017-05-24 19:39:41 -0500 | marked best answer | temperature control;Tolerance temperature I want to know how can I set the "Tolerance temperature" in E+ which is the temperature control. The situation can be describe that I want to use AC when the room temperature is higher than 29 ℃,but if I use AC the cooling setpoint is 26 ℃. So which temperature should I fill in |
2017-05-24 08:37:25 -0500 | commented answer | temperature control;Tolerance temperature Thank You for your answer.Now I want to set EMS contorl with IdealLoadAirSystem.The sensor is one zone's mean air temper |
2017-05-21 21:33:38 -0500 | commented question | how to estimate air change rate under natural ventilation mode Do you solve you problem that the calculation of air change rate under natural ventilation mode |
2017-05-21 08:33:01 -0500 | asked a question | temperature control;Tolerance temperature temperature control;Tolerance temperature Hi,everyone,I want to konw how can I set the "Tolerance temperature" in E+ wh |
2017-04-12 21:12:38 -0500 | commented answer | Natural Ventilation Control thank you! I have found the 'Natural Ventilation' and I want to know if it can decide when to ventilate through calculating the room tenperature |
2017-04-11 21:15:12 -0500 | received badge | ● Supporter (source) |
2017-04-11 21:15:02 -0500 | received badge | ● Scholar (source) |
2017-04-10 21:26:56 -0500 | commented answer | The cooling load of result report is 0 in openstudio thank you! I can get the cool load while I set the Heating Thermostat Schedule. |
2017-04-10 00:37:09 -0500 | received badge | ● Student (source) |
2017-04-10 00:34:46 -0500 | asked a question | Natural Ventilation Control Everyone, I want to know how can I control the natural ventilation depanding on the outdoor temperature in openstudio? |
2017-04-10 00:34:45 -0500 | commented question | Can I set the natural ventilation depending of temperature and CO2 ppm? Do you get the solution ? Can I ask you for help? |
2017-04-09 08:59:09 -0500 | asked a question | The cooling load of result report is 0 in openstudio I made a simple model with the ideal air load system, I only want to see the room load in the natural situation. But the cooling load from the output report is 0. Can anyone give me some tips? I have set Cooling Thermostat Schedule |
2017-02-28 09:31:00 -0500 | commented question | Severe error caused by Controller Mechanical Ventilation (OpenStudio 1.5.0) I met the same problem,but I can't make sure if I was missing design day,can you tell me how to check? |