Guinha's profile - activity

Hello guys, I’m trying to add frames and divider from the Open Studio library in all my windows but the simulation show this error:

* Severe * ProcessSurfaceVertices: Base Surface="SURFACE 228", * ~~~ * Window Surface="SUB SURFACE 15" area (with frame) is too large to fit on the surface. * ~~~ * Base surface area (-windows and doors)=[0.13] m2, frame area=[0.71] m2.

In my model, there is two cases:

How can i add a frame without result in a error?

Thanks

Frame's area too large Hello guys, I’m trying to add frames and divider from the Open Studio library in all my windows

Frame's area too large Hello guys, I’m trying to add frames and divider from the Open Studio library in all my windows

Frame's area too large Hello guys, I’m trying to add frames and divider from the Open Studio library in all my windows

Best way to model a ceiling and raised floor Hello guys, I am developing a simulation of a four-story floors building wi

Multiple equipment to the same zone Hello guys! I need to simulate 2 zone that have 6 self contained refrigerating bot

Hello all,

I’m simulating a datacenter and the simulation shows a high cooling load. The internal equipment load is 276,3 Kw from racks and the cooling load is 362,97 Kw. Why this happen? How can I find this extra load? The Simulation has a measure that shows all loads from a zone. (Second image)

About the model:

Construction External wall: All external wall is adiabatic - no Sun and no Wind

Internal Loads People: zero

Infiltration: zero

Outdoor Air: zero

Equipment: 276,3 Kw (total)

Equipment Schedule (fraction): 1

Light: 11.84 W/m² Office_IT_Room Lights

Setpoint:

Datahall: 27C

Central Cooling Design Supply Air Temperature: 14C

File- https://drive.google.com/open?id=1IHe...

Thank's!

(/upfiles/15198405231969875.png)

The problem is just in the simple unit conversion. The internal load was 63000 W, but the correct load is 6300 W. All t

Guys! The problem is just in the simples unit conversion.

High cooling load Hello all, I’m simulating a datacenter and the simulation shows a high cooling load. The internal eq

Of Corse! I'll add the file in a link.

High cooling load Hello all, I’m simulating a datacenter and the simulation shows a high cooling load. The internal eq

High cooling load Hello all, I’m simulating a datacenter and the simulation shows a high cooling load. The internal eq

Hi @rsunnam! Yes! I've checked all loads.

High cooling load Hello all, I’m simulating a datacenter and the simulation shows a high cooling load. The internal eq

High cooling load Hello all, I’m simulating a datacenter and the simulation shows a high cooling load. The internal eq

High cooling load Hello all, I’m simulating a datacenter and the simulation shows a high cooling load. The internal lo

I’m simulating a datacenter and the simulation shows a high cooling load. The internal load is 276,3 Kw and the cooling

I’m simulating a datacenter and the simulation shows a high cooling load. The internal load is 276,3 Kw and the cooling

I’m simulating a datacenter and the simulation shows a high cooling load. The internal load is 276,3 Kw and the cooling

Well, I downloaded Sketchup 2016 and OpenStudio 1.10.0. I did all my geometry and saved it. When I open the same Project, i get the following Messenger : Removing previously linked OpenStudio content. Open OpenStudio model at “to restore contente”

Hello all!

I was running a file in the last version and got an error. The error file (stderr) was outside the running's folder and totaly empty. How can i find this folder? There is another way to find the error?

The message: **FATAL:IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination. EnergyPlus Run Time=00hr 00min 1.02sec Failed.

Link: https://drive.google.com/open?id=1IHe...

Thanks

@Avi, It's work!!!! Thank you so much!!!!! :) :) :)

@Avi, It's work!!!! Thank you so much!!!!!

@mdahlhausen I couldn't find the sterr file in the run folder. I'm going to add an image of what I see in the run folder

It's interesting because I can't see this folder inside the run folder.

@Avi, thank you for show me the error.

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

@mdahlhausen I couldn't find the sterr file in the run folder. I'm going to add an image of what I see in the run folder

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

@mdahlhausen and @Avi , I added two photos of the error file and the file link. I hope the material will help you. Than

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

@mdahlhausen and @Avi , I added two photos of the error file and the file link. I hope the material will help you.

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

Thanks, @Avi ! I'll correct.

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file (stder

Error file is totaly empty Hello all! I was running a file in the last version and got an error. The error file was ou