some severe errors in open studio

edit

There is a severe error that confuse me. How to solve "convergence error in SolveForWindowTemperatures for window"?

Program Version,EnergyPlus, Version 23.1.0-87ed9199d4, YMD=2023.12.28 10:11,
************* Beginning Zone Sizing Calculations
** Warning ** ProcessScheduleInput: Schedule:Constant="ALWAYS OFF DISCRETE", Blank Schedule Type Limits Name input -- will not be validated.
** Warning ** ProcessScheduleInput: Schedule:Constant="ALWAYS ON CONTINUOUS", Blank Schedule Type Limits Name input -- will not be validated.
** Warning ** GetHTSurfaceData: Surfaces with interface to Ground found but no "Ground Temperatures" were input.
**   ~~~   ** Found first in surface=SURFACE 20
**   ~~~   ** Defaults, constant throughout the year of (18.0) will be used.
** Warning ** GetSurfaceData: Construction INTERIOR WINDOW of interzone surface SUB SURFACE 28 does not have the same materials in the reverse order as the construction INTERIOR WINDOW of adjacent surface SUB SURFACE 48
**   ~~~   ** or the properties of the reversed layers are not correct due to differing layer front and back side values
**   ~~~   ** ...but Nominal U values are similar, diff=[0.0000] ... simulation proceeds.
**   ~~~   ** ...if the two zones are expected to have significantly different temperatures, the proper "reverse" construction should be created.
**   ~~~   ** ...this problem for this pair will not be reported again.
** Warning ** CalculateZoneVolume: 2 zones are not fully enclosed. For more details use:  Output:Diagnostics,DisplayExtrawarnings; 
** Warning ** CheckUsedConstructions: There are 5 nominally unused constructions in input.
**   ~~~   ** For explicit details on each unused construction, use Output:Diagnostics,DisplayExtraWarnings;
** Warning ** GetSimpleAirModelInputs: ZoneInfiltration:DesignFlowRate="SPACE 107 189.1-2009 - SECSCHL - KITCHEN - CZ4-8 INFILTRATION", Design Flow Rate Calculation Method specifies Flow Rate per Exterior Surface Area, but Exterior Surface Area = 0.  0 Infiltration will result.
** Warning ** GetElectricEIRChillerInput: Chiller:Electric:EIR="CHILLER ELECTRIC EIR 1"
**   ~~~   ** Energy input ratio as a function of temperature curve output is not equal to 1.0 (+ or - 10%) at reference conditions.
**   ~~~   ** Curve output at reference conditions = 0.861
** Severe  ** Convergence error in SolveForWindowTemperatures for window SUB SURFACE 65
**   ~~~   **  During Warmup & Sizing, Environment=BEIJING ANN CLG .4% CONDNS DB=>MWB, at Simulation time=07/21 05:10 - 05:20
**  Fatal  ** Program halted because of convergence error in SolveForWindowTemperatures for window SUB SURFACE 65
...Summary of Errors that led to program termination:
..... Reference severe error count=1
..... Last severe error=Convergence error in SolveForWindowTemperatures for window SUB SURFACE 65
************* Warning:  Node connection errors not checked - most system input has not been read (see previous warning).
************* Fatal error -- final processing.  Program exited before simulations began.  See previous error messages.
*************
************* ===== Final Error Summary =====
************* The following error categories occurred.  Consider correcting or noting.
************* Nominally Unused Constructions
************* ..The nominally unused constructions warning is provided to alert you to potential conditions that can cause
************* ..extra time during simulation. Each construction is calculated by the algorithm indicated in the HeatBalanceAlgorithm
************* ..object. You may remove the constructions indicated (when you use the DisplayExtraWarnings option).
*************
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 8 Warning; 1 Severe Errors.
************* EnergyPlus Terminated--Fatal Error Detected. 8 Warning; 1 Severe Errors; Elapsed Time=00hr 00min  0.57sec

Thanks