**FATAL:CalcCoordinateTransformation: Program terminates due to preceding condition.
This is a message from eplusout.err after I run Simulation. I try to write model again but the result is the same. Please Help me.
Program Version,EnergyPlus, Version 9.3.0-baff08990c, YMD=2020.10.27 14:49,
************* Beginning Zone Sizing Calculations
** Warning ** ProcessScheduleInput: Schedule:Constant="ALWAYS_ON", Blank Schedule Type Limits Name input -- will not be validated.
** Warning ** ProcessScheduleInput: Schedule:Constant="ALWAYS OFF DISCRETE", Blank Schedule Type Limits Name input -- will not be validated.
** Warning ** ProcessScheduleInput: Schedule:Constant="ALWAYS ON CONTINUOUS", Blank Schedule Type Limits Name input -- will not be validated.
** Warning ** GetHTSurfaceData: Surfaces with interface to Ground found but no "Ground Temperatures" were input.
** ~~~ ** Found first in surface=SURFACE 199
** ~~~ ** Defaults, constant throughout the year of (18.0) will be used.
** Warning ** GetSurfaceData: Entered Zone Floor Areas differ from calculated Zone Floor Area(s).
** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual zones.
** Warning ** GetSurfaceData: Very small surface area[6.61226E-005], Surface=SURFACE 4173
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4593
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4243
** Warning ** GetSurfaceData: Very small surface area[6.61226E-005], Surface=SURFACE 4203
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4227
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4440
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4412
** Warning ** GetSurfaceData: Very small surface area[6.61226E-005], Surface=SURFACE 4417
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4565
** Warning ** GetSurfaceData: Very small surface area[6.61226E-005], Surface=SURFACE 4570
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4746
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4719
** Warning ** GetSurfaceData: Very small surface area[6.61226E-005], Surface=SURFACE 4724
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4898
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 4871
** Warning ** GetSurfaceData: Very small surface area[6.61226E-005], Surface=SURFACE 4876
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 5051
** Warning ** GetSurfaceData: Very small surface area[9.98026E-005], Surface=SURFACE 5020
** Warning ** GetSurfaceData: Very small surface area[6.61226E-005], Surface=SURFACE 5025
** Warning ** GetSurfaceData: Very small surface area[1.46053E-004], Surface=SURFACE 5212
** Warning ** GetSurfaceData: Very small surface area[9.67648E-005], Surface=SURFACE 5339
** Warning ** GetSurfaceData: Very small surface area[1.46053E-004], Surface=SURFACE 5186
** Warning ** CalcSurfaceCentroid: 17 Surfaces have the Z coordinate < 0.
** ~~~ ** ...in any calculations, Wind Speed will be 0.0 for these surfaces.
** ~~~ ** ...in any calculations, Outside temperatures will be the outside temperature + 9.750E-003 for these surfaces.
** ~~~ ** ...that is, these surfaces will have conditions as though at ground level.
** Warning ** GetSurfaceData: There are 215 coincident/collinear vertices; These have been deleted unless the deletion would bring the number of surface sides < 3.
** ~~~ ** For explicit details on each problem surface, use Output:Diagnostics,DisplayExtraWarnings;
** Severe ** GetSurfaceData: There are 61 degenerate surfaces; Degenerate surfaces are those with number of sides < 3.
** ~~~ ** These surfaces should be deleted.
** ~~~ ** For explicit details on each problem surface, use ...
It would be good to have some additional information on the source of the geometry from he model, as that is where the problem lies. If you are using the SketchUp Plugin there is a diagnostic script that can make a copy of your OSM with many objects like this removed, but while that might get the model running, it may not be as expected. You should inspect the output in that case to see if the geometry looks like it should.